November 6, 2026

How to set up drip irrigation for tomatoes

Lay the drip line along the row, put an emitter on each side of every tomato, and run it until water soaks the root zone. Then leave it off until the bed reads dry. Tomato roots spread wider than the leaves by midsummer, so emitters left at the stem miss most of the feeding roots. Steady moisture also heads off the dry-then-soaked swings that split fruit and cause blossom end rot.

Why drip suits tomatoes

Drip puts water on the soil and keeps it off the leaves. Leaf diseases such as early blight spread when spores land on wet foliage and germinate, so dry leaves slow them down. Water from an emitter spreads underground in a bulb. In sandy soil the bulb runs deep and narrow. In clay it spreads wide and shallow, because fine pores pull water sideways faster than gravity pulls it down.

Steady moisture matters for the fruit. Calcium reaches a growing tomato in the water stream, so a dry spell starves the blossom end and leaves a dark sunken patch. When water floods back in after that dry spell, the fruit swells quicker than its skin can give, and the skin cracks.

Step 1. Lay the line along the row

Run the tubing on the soil surface beside the plants, on the side you can reach. A single row of tomatoes needs one line. A second row needs its own line, because an emitter's wet bulb won't reach across the bed.

Step 2. Put an emitter on each side of the stem

At transplanting, the roots sit inside the root ball. Place the emitters close enough that their wet bulbs reach it. Water that lands far out drains past soil the roots haven't reached yet.

Step 3. Move the emitters outward as the plant grows

By the time the plant sets fruit, its feeder roots reach out past the leaves. Shift the emitters or add more toward the edge of the canopy. Water left at the stem keeps the crown wet, which invites rot, while the feeding roots go short.

Step 4. Cover the line with mulch

Mulch shades the soil, so less water leaves the surface by evaporation. It also shades the tubing, which keeps the plastic from heating and creeping out of place. Keep the mulch a little back from the stem so the crown stays dry.

Step 5. Find your run length with a trowel

Run the line, let the water soak in, then dig a narrow hole beside an emitter. You want moist soil down through the root zone and out toward the next emitter. If the wet patch stops short, run longer next time. If water pools or runs off the bed edge, the soil can't absorb it that fast, so split the run into two shorter ones with a pause between.

A probe makes this easier to read. Suppose your bed reads 28% on a Tuesday morning, and after a run the probe climbs to 41% by afternoon. That rise tells you the water reached the probe's depth. Note how long the run took and use it as your starting length.

Step 6. Put a soil probe in the root zone

Push the probe into the soil between the stem and an emitter, at the depth where roots feed. A probe directly under an emitter reads wet long after the rest of the bed has dried. A probe outside the wet bulb reads dry while the roots are fine. Our guide to setting up a raised tomato bed with a sensor covers placement in more detail.

Map the probe to its bed in the station screen so its readings count for that bed. On Pro, a soil probe mapped to a bed sends a dry alert when the two most recent readings are both below 25%, or both above 60 cb on a Watermark probe. You get at most one dry alert per bed per day.

Step 7. Run the line when the bed is dry and hold it when rain is due

The dry alert is your cue to run the line for the length you found in step 5. Siltwell tells you which bed is dry and leaves the watering to you. On any plan, the Today screen shows garden-level watering guidance. A forecast of 5 mm or more across today and tomorrow turns the watering guidance on the Today screen to hold. Rain of 5 mm or more in the last three days turns it to covered.

That guidance covers the whole garden. A bed under an eave or a dense canopy can stay dry while the guidance reads covered, and the bed's own probe catches that. In our own garden the tomato bed ran between 36% and 57% moisture from mid-July to early September. Its readings stayed well clear of the 25% line through a July that delivered 10.89 inches of rain.

What can go wrong

  • Clogged emitters. Grit and minerals in the water block the small openings. One wilting plant in an otherwise wet row usually points to a clog, so flush the line from its far end.
  • Weak flow at the far end. Friction in the tubing drops pressure along a long run, so the last plants get less water. Pressure-compensating emitters hold their flow, as our guide to drippers per bed explains.
  • A timer running through wet weeks. Saturated soil pushes air out of the root zone, and roots short of oxygen stop taking up water. Pause the timer when the guidance says hold or covered.
  • A big soak after a long dry gap. Ripening fruit swells fast when water floods back in, and the skin splits. Water at the first dry alert so the gap never gets long.

Each probe measures only the soil close to its tip. It has no way to tell you that the emitter at the far end of the row has clogged, so walk the line now and then and check that each emitter leaves a wet spot.

Fruiting tomatoes in summer heat pull water fastest, so the days between dry alerts shrink in midsummer and stretch again in fall. Our guide to how often to water tomato plants walks through how that interval changes across the season.

Common questions.

What is better, drip or soaker hose?
For tomatoes, drip usually works better because emitters put water at set points beside each plant. A soaker hose weeps along its whole length, and its output falls toward the far end as pressure drops. A soaker hose suits a dense bed where every inch of soil holds roots. Widely spaced tomatoes waste less water on drip.
What is the best way to irrigate a raised bed garden?
Give each raised bed its own drip line and decide on each bed separately, because beds dry at different rates. Soil depth, sun, and what's planted all change how fast a bed loses water. In our own garden, three raised beds of the same size ran different moisture ranges through the same summer, from 39% to 54% in one and 32% to 62% in another. A soil probe in each bed tells you which one needs a run.
How long should you run drip irrigation for tomatoes?
Run it until water reaches the root zone, which you find by digging beside an emitter after a run. The right length depends on emitter flow, soil texture, and how dry the bed was, so it varies from bed to bed. Once you know your length, keep it and change how often you run the line instead. A soil probe in the bed tells you when the next run is due.
Where should drip emitters go on tomato plants?
At planting, put an emitter on each side of the stem, close enough to wet the root ball. As the plant grows, move the emitters out toward the edge of the leaf canopy, where the feeder roots spread. Keep water off the stem itself, since a wet crown invites rot.

Related guides

Free planting tools

  • When to plant shows the last date to sow each crop before your fall frost.
  • Microclimate checker shows how much colder or warmer gardens near you ran than the forecast low.
  • GDD estimator adds up a typical season's heat and shows which crops can ripen where you are.
Siltwell

Made for your microclimate

Get frost alerts you can adjust for your yard.